Same-day callouts across SydneyMon – Sun: 7am–6pmSend a photo quote0468 497 928
Quote now

Broken glass is a safety job — we prioritise it

Shower Screen Glass Replacement Sydney

Cracked, chipped or shattered glass? In most bathrooms we take out the broken panel and fit a new one. The frame, the door hardware and the rest of the screen stay right where they are.

SRWritten by the Shower Screen Repair team and reviewed by our licensed glaziersLast updated 7 October 2026About our glaziers

If the glass has already shattered, do this first

Five things, in order. Two minutes of care here is worth it.
  1. 1Keep everyone out of the bathroom. Bare feet and pets first.
  2. 2Do not pull at the leftover glass. A broken panel often keeps dropping pieces for hours.
  3. 3Take one photo from the doorway. That is enough for us to price it.
  4. 4If pieces are still falling, lay an old towel along the base to catch them.
  5. 5Ring us. We clear the glass and board the opening if this is your only bathroom.

Can you replace just one panel?

Yes. On most Sydney shower screens, a single cracked or chipped panel comes out on its own and a new one goes back in. You rarely need a whole new screen. The new piece is measured at your place and cut to fit, so the job normally takes two visits a few days apart.

Shower glass is tough. It has to be. But it has two weak spots: the edges and the corners. Knock either one and the panel can let go, sometimes straight away, sometimes weeks later.
This page covers how a panel swap works, why toughened glass fails the way it does, and why the job takes a few days rather than an hour.

Cracked, chipped or shattered — which one is yours?

The three look very different, and so does the job.
A chip on the edgeA small bite out of the edge or corner. It looks minor. It is not. The edge is the strongest part of the panel, so a chip there is the most likely place for the whole thing to give way later. This is the one people leave too long.
A crack running throughA line across the glass, often with a starting point you can feel. Once a panel is cracked it is done. Toughened glass cannot be filled, glued or polished back.
Shattered into piecesThe panel has let go and the glass is sitting in the base or across the floor in small blunt chunks. Follow the five steps above before you touch anything.
If the glass is already down, that is an emergency job rather than a planned one. We cover it under broken shower screen callouts.

How a single panel swap works

Most screens are built from separate pieces held in a frame or on brackets. That is good news. It means one piece can come out while everything around it stays put.
On a framed or semi-frameless screen, the panel sits in a channel. The glazier takes the beading off, lifts the old glass clear, cleans the channel and sets the new piece in. On a frameless screen the panel is held by brackets or hinges instead, so those come off first and go back on afterwards.
If the broken piece is the door rather than a fixed panel, the hardware comes off the old glass and goes onto the new one. Worn hinges or a tired catch are usually worth changing at the same time, since the door is already down — that side of things is covered on shower screen door repairs.

Why toughened glass breaks the way it does

Shower glass is toughened, which means it is heated and cooled quickly when it is made. That leaves the surface under tension and makes the panel several times stronger than ordinary glass.
Ordinary glassBreaks into long, sharp pieces. That is why it is not allowed in a shower.
Toughened glassBreaks into small blunt chunks that hold loosely together. Far safer, and required by AS 1288.
That trade-off is the whole point. Toughened glass is harder to break, and when it does go it goes into pieces that will not cut you badly.
It also explains two things people find strange. A chipped edge matters because the tension is highest there. And a screen can break hours or even days after the knock that caused it, which is why nothing was obviously wrong at the time.

What thickness of glass will you get?

We match what is already there, unless the screen is being rebuilt. Thickness is set by the design, not by preference.
4–5mmOlder framed screens. Needs the frame around it for support. Still common in homes built before the 2000s.
6mmMost framed and semi-frameless screens. The one we fit most often.
8mmSome semi-frameless doors. Sits between the two. Less common.
10mmFrameless screens. Heavy. It holds itself up, so the hardware has to be right.

Bars shown to relative scale.

Every panel we supply is Grade A safety glass to AS 1288, the Australian rule for glass in buildings. It comes stamped in one corner so you can see it. If we find ordinary glass in an older screen, we will tell you, because that is a real safety problem and not a sales pitch.

Why it takes two visits

This is the part that surprises people, so it is worth explaining properly.
Toughened glass has to be cut, shaped and drilled before it is toughened. After that it cannot be touched. Cut a toughened panel and it falls apart on the bench. So we cannot carry blanks in the van and trim one to fit.
On top of that, almost no bathroom is perfectly square. A panel cut to the measurement on the old glass often will not go back in, because the old piece was itself cut to suit a slightly off opening.
1
MeasureThe glazier measures the opening at your place, checks it for square, and notes any holes needed for hinges or a handle.
2
MakeThe panel is cut, edges polished, holes drilled, then toughened. This is the part that takes a few days.
3
FitWe come back, set the new glass in, refit the hardware and run water over it to check the seal. Usually about an hour.
Polished edge and new toughened shower screen panel

What changes the price

We do not put a single figure on this page, because glass is priced by the piece and no two screens are the same. Five things move it:
  • Thickness. A 10mm frameless panel costs a good deal more than a 6mm one of the same size.
  • Size. Taller than about 2100mm and the panel needs two people to lift and fit.
  • Holes and cut-outs. Hinge cut-outs and handle holes are all done before toughening, so they add to the piece.
  • Door or fixed panel. A door takes longer, because the hardware has to come off and go back on square.
  • Access. A ground-floor bathroom is simpler than a third-floor unit with a tight stairwell.
Send a photo and your suburb and you will get a range back, usually the same day. There is no charge for that.

Where we replace shower glass

We cover metropolitan Sydney. Measuring can normally be done the same day or the next, with the fit booked once the glass is ready.

Common questions

No. A crack in toughened glass cannot be filled, glued or polished out. The strength of the panel comes from tension held inside the glass, and once that is broken the piece has to come out. The good news is that only the broken piece needs to go. Everything around it stays.

We would not. A cracked panel can hold for weeks and then let go without warning, usually when the door is knocked or the room heats up. If it is the only shower in the house, use it carefully, keep children and pets out, and get it looked at quickly. If there is another bathroom, use that one until the glass is changed.

Almost always there was damage first, usually a small chip on an edge or corner that nobody noticed, and the panel finally gave way days or weeks later. Heat changes in the room can be the final push. Very rarely a tiny flaw inside the glass causes it instead, which is a known fault in toughened glass and nothing you did.

Because toughened glass is cut and drilled before it is toughened, not after. Once a panel has been through that process it cannot be trimmed at all. Try it and the sheet breaks apart. So the measurement has to go to the glass works and the piece is made to your opening.

In a clear glass screen, yes. Clear toughened glass has a slight green tint in the edge and the new piece will have the same. Patterned or frosted glass is harder, because older patterns get discontinued. If we cannot match it we will say so before you commit, and then it becomes a choice between a close match and replacing more than one panel.

The measure takes about twenty minutes. The glass itself normally takes a few working days to be made. Fitting is around an hour for a fixed panel and a little longer for a door. If the panel has already shattered we clear the glass on the first visit so the bathroom is safe in the meantime.

Yes. Broken glass goes with us, including anything we clear out of the base and the channel. Nothing is left in your bin.

Sometimes, but it is worth thinking about. If the aluminium has gone chalky and soft at the base it will not hold a new panel properly, and you would be paying for glass that has to come out again later. In that case we would quote the frame at the same time, or talk about a new screen if both are past it.

Related glass work

On every glass job

  • Grade A safety glass to AS 1288, stamped
  • Measured at your place, cut to your opening
  • Old glass taken away
  • Licensed glaziers, fully insured
Quote now
Quote now